|
|
Other side of my hanging kite... |
Let me take a moment to acknowledge that this idea is certainly not original.
I've seen other people's versions and I'm sure they've left enough of an
impression on me to influence this project. To be sure, I'm not taking credit
for making a decorative kite out of fabric.
That said, I haven't seen one made in exactly this way, using either the strip method I posted about last week or the scrappy method that I'm going to show you here.
Perhaps I can take a bit of credit for coming up with a unique take on the
fabric kite. ;-)
Regardless of how big your kite project is, any sewer can make one using
this method. Quite literally, you are going to cover your kite template with
fabric scraps.
You will need some fusible fleece and some 1/2" double folded (i.e., 2" unfolded) bias or regular straight binding to finish.
Method #2: Hanging Kite Using Fabric Scraps
Because I'm making a double-sided item, I used the back of the other side
of the kite as a cutting template for the fusible fleece (fusible side
up).
|
| Method #2... |
Then I laid down a bunch of coordinating fabric scraps until the entire
surface was covered. This was just a preliminary step to ensure that I had
enough fabric; I was still going to fiddle with the final arrangement.
|
| Scraps pinned down... |
I ironed some of the more crinkly pieces and then started pinning them onto the fusible fleece. There is some overlap, but for the most part I tried to puzzle piece them. My aim was to have the darker gray pieces to one side. (My fabric scraps were Robert Kaufman, Tim Holtz and "no name" sheet and pillow case remnants.)
Once satisfied with the placement of the scraps, I fused them onto the fleece and then contemplated how to quilt the surface.
|
| A form of echo quilting... |
I chose to do an echo quilting technique around each half of the surface. (While I was doing it, though, I again wondered how people can enjoy quilting and quilting and quilting large surfaces. Sadly, it's not my thing.)
So quilt it or not, it's up to you. But even though I'm not a fan of the process, there's no doubt that quilting the surface makes it look a lot nicer... and it adds even more textural interest beyond the scrappy-ness of the piecing.
|
| Worthwhile quilting job... |
If intended as a wall hanging, the edges can now be bound and finished off.
Otherwise, pin it back to back with the other piece and baste the edges
together.
|
| Baste both pieces together... |
Keep the seam allowance as small as possible when basting.
|
| Clip binding to "back" side of kite... |
Clip the binding — right side down — to the edge of whichever side you deem is
the "back" side of the kite. Start at the tip of the kite and work your way
around (leave enough binding to finish off with a tail).
The inset picture above shows how to turn the corners.
Sew the binding with just under 1/2" seam allowance; i.e., just short of the first fold. Then flip it around to the other side and clip again. Finish sewing the binding from the "right" side.
|
| Turn binding to the right side and finish sewing... |
As you can see in the above picture, my 13" square of fabric left me with just enough bias binding to make it all the way around. (The 1" wide strip of fabric that remained was then folded in half and sewed up; some artful tucking and stitching later, it was secured as the tail.)
|
| Kite with a tail... |
However you choose to add a tail and finish off the binding will be fine; it's
a simple matter of making it work. I'm not going to describe any particular
process for it.
|
| Tie fabric scraps to the tail to complete the look... |
If you made the other half of the kite as detailed last week, you can take
some of the fabric scraps you sliced off the edges of the quadrants and tie
them to the kite tail. (If not individually big enough to tie, you can sew them together
first.)
|
| Got wire? Give your kite tail the illusion of movement... |
A long time ago, I harvested the wire out of some wired ribbon (which I then used to make some zipper pulls). I inserted
some into the kite tail to give it the ability to bend. (Yes, I thought that
was clever of me too.)
One final photo to share... this is how I hung it up in the window.
|
| A solution to the "how to hang" problem... |
The little clip is from a bag of Hawaiian coffee (a small binder clip will do the job just as well) and the gold cord is left
over from my
personal project portfolio. I clipped it along the top — about six inches away from the peak — so that
it hangs at an angle. Because after all, a kite rarely flies straight up and
down.
A bit of an update... I've had this in my window since late March, with the vibrant stripey side facing out. However, this scrappy side
has grown on me, so I might consider alternating the display at
some point. I also had a thought that making smaller versions and hanging them from a ceiling might result in a fun display.
What do you think?
'Til next...
No comments:
Post a Comment
You have the power to brighten my day. Leave me a comment; I'd love to hear your thoughts... you can even remain ANONYMOUS! And rest assured that I acknowledge all comments, either here or via email. (That is, if you don't see a response from me here, I would have responded privately to the person.) Spam or generic comments with unrelated links, however, are promptly removed... and I may take appropriate action or report you to Google. Thanks for reading! (✿◠‿◠)